1050D Dynamic Torque Sensor for Dynamic Micro Torque Measurement

1050D Dynamic Torque Sensor for Dynamic Micro Torque is an integrated product composed of resistance strain sensitive components and integrated circuits. It is made of alloy steel/stainless steel material. The structural design has a small size range and high precision. The output terminal of positive and negative torque signals is the key link. The instantaneous speed can reach 4000 rpm. It is widely used in all kinds of small-scale torque measurement such as micro-motors, viscometer rotating power equipment systems, etc.

Features of 1050D Dynamic Torque Sensor

  • Based on the principle of resistance strain type, power supply and signal output are realized through brushes.
  • Various small-scale torque measurements. It can measure the torque value in both forward and reverse directions.
  • Both ends are connected by shaft keys, which is easy to install and use.
  • The maximum speed does not exceed 4000 rpm.

Technical Parameters

ParametersSpecifications
Range0-10,20,30,50,100,200,500,1000Nm
Sensitivity1.5±10% mV / V
Zero output±2% F.S.
Nonlinear±0.1,0.3% F.S.
hysteresis≤±0.05% F.S.
Repeatability≤±0.05% F.S
Creep≤±0.03% F.S/30min
Temperature Sensitivity Drift0.03% F.S. / 10℃
Zero temperature drift0.03% F.S. / 10℃
Input resistance750±10Ω
Input resistance700±5Ω
Insulation resistance≥5000MΩ/ 100VDC
Excitation voltage10-15VDC
Temperature Compensation Range-10 ~ 60ºC
Range of working temperature-20 ~ 80ºC
Safe overload150% F.S.
Extreme overload200% F.S.
Cable sizeØ5.2×3m
Electrical connectionsRed/E+, Black/E-, Green/S+, White/S-
MaterialStainless or Alloy Steel

Dimensions

Dimensions of 1050D Dynamic Torque Sensor

Frequently asked questions

Dynamic torque: It is the torque displayed in real time during the assembly process, when the fastener is fastened. That is, the dynamic torque that the power tool applies to the bolt, overcoming the friction. The axial preload force for the bolts generated by the dynamic torque meets the engineering requirements for the preload force. Generally, the torque value preset by the tool or equipment is the dynamic torque value.

The dynamic torque sensor provided by Sino-Inst is a resistance strain dynamic torque sensor. dynamic torque sensor Torque measurement using strain gauge technology.

A strain bridge is formed on the elastic axis. The electrical signal of the elastic shaft being twisted can be measured by supplying power to the strain bridge. After the strain signal is amplified, it undergoes pressure/frequency conversion. becomes a frequency signal proportional to the torsional strain.

What is the purpose of the force torque sensor?

The force torque sensor is divided into two categories: dynamic and dynamic. Force torque sensor is the detection of torque torque perception on various rotating or non-rotating mechanical parts. And convert the physical changes of torque into precise electrical signals.

The force torque sensor can be used in the manufacture of viscometers, electric (pneumatic, hydraulic) torque wrenches. It has the advantages of high precision, fast frequency response, good reliability and long life.

Field of application of force torque sensor:

  1. AC (DC) motor, servo motor, stepper motor;
  2. Control and inspection of the machining process of automobile engines, diesel engines, steering gears, the overall rigidity and torsion of the body and other components;
  3. Electric (manual) actuator, automatic opening and closing control of various valves.
  4. Control and monitoring of oil extraction and refining process, monitoring of thermal (water) power generation equipment, ore screening control, and monitoring of wind power generation equipment.
  5. Torque life test of various materials.
  6. Process control of railway machinery and equipment, etc. details as follows:
    1. Detect the output torque and power of rotating power equipment such as generators, motors, and internal combustion engines.
    2. Detect the load torque and input power of reducers, fans, pumps, mixers, winches, propellers, drilling machinery and other equipment.
    3. Detect the torque in the working process of various machining centers and automatic machine tools.
    4. The torque transmitted by various rotating power equipment systems is extremely efficient.
    5. It can detect the rotational speed and axial force while detecting the torque.
    6. It can be used to manufacture viscometers, electric (pneumatic, hydraulic) torque wrenches.

Torque sensors are not common in our daily life, but their application is very important.
The torque sensor on the car checks the torsional deformation of the torsion bar and converts it into an electrical signal. This electrical signal is transmitted to the electric power steering system under the battery.

The sensor consists of phase splitter units 1 and 2 and a torsion bar. Sensor 1 is located on the steering spindle and sensor 2 is located on the pinion shaft. After the torsion bar is rotated, the two phase splitter units create a relative angle.

The converted voltage signal is transmitted to the electric power steering system. The electric power steering system determines the corresponding working voltage of the EPS steering motor according to the relative resistance. The location of the two cells is also used above.

  1. The electric power steering system only starts the motor to generate electricity when steering is required. This can reduce the fuel consumption of the engine.
  2. It can provide power under various driving conditions. Reduce motor unevenness. The output torque of the motor is assisted by the action of the transmission. Assist system interference, improve the vehicle’s steering characteristics, and improve the vehicle’s active safety.
  3. Without hydraulic circuit, it is easier to adjust and detect. Assembly automation is higher. Different models can be quickly matched by setting different programs. Shorten production and development cycles. No oil leakage problem, reduce environmental pollution.

Electric power steering systems primarily use torque sensors to detect the magnitude and direction of torque or the angle produced by the steering wheel when the driver steers. And convert the required information into digital signal input control unit. Then there is the axis control unit pair.

These signals are calculated to obtain a torque compatible with the driving conditions. And this command is used to drive the motor to work. The output torque of the electric motor is assisted by the action of the transmission.

It’s not hard to see that torque sensors are very important. Damage to the car’s torque sensor directly causes the car to lose its steering assist function during driving. Stiff steering failure.

Such torque sensors are very important in automotive safety issues. The quality of the torque sensor directly determines the safety factor of the car.

If you cannot find an answer to your question in our FAQ, you can always contact us
and we will be with you shortly.

More Featured Torque Sensors

Sino-Inst is a manufacturer of 1050D Dynamic Torque Sensor for Dynamic Micro Torque Measurement-5Nm. We offer more than 10 types of Dynamic Torque Sensors. Dynamic Torque Sensors can measure a variety of different mechanical power, rotational speed and torque measuring devices.

Dynamic Torque Sensors are widely used in the following areas:
Application in process industry and process industry;
In sewage treatment systems, measure the relevant power and torque;
Measure the power and torque of machinery such as aircraft, ships, railway locomotives and mines;
Can be used to make viscometers;
Measuring the output power and torque of related devices such as internal combustion engines and rotational forces;
Measure power and torque of torque wrenches, water pumps, etc.

Dynamic Torque Sensor is also called rotary torque transducer, torque transducer. Mainly used for torque measurement in dynamic situations. The dynamic torque sensor is equipped with a speed measuring device, which can measure the rotational speed while measuring the torque. At this time, the torque sensor can also be called a torque speed sensor.

Sino-Inst’s Dynamic Torque Sensor, made in China, have good quality, with better prices. Our Dynamic Torque Sensors are widely used in China, India, Pakistan, USA and other countries.

Sino-Inst’s entire team is well trained, so we can ensure that each customer’s needs are met. If you need any help with your product requirements, whether it is a Dynamic Torque Sensor, level sensors, or other equipment, please give us a call .

Request a Quote

1050D Dynamic Torque Sensor for Micro Torque-0.1,0.5,1-5Nm

1050D Dynamic Torque Sensor for Dynamic Micro Torque is an integrated product composed of resistance strain sensitive components and integrated circuits. It is made of alloy steel/stainless steel material. The structural design has a small size range and high precision. The output terminal of positive and negative torque signals is the key link. The instantaneous speed can reach 4000 rpm. It is widely used in all kinds of small-scale torque measurement such as micro-motors, viscometer rotating power equipment systems, etc.

Product SKU: 1050D Dynamic Torque Sensor for Dynamic Micro Torque Measurement

Product Brand: Sino-Inst

Price Valid Until: 2029-09-09

Product In-Stock: InStock

Editor's Rating:
5

Leave a Reply

Your email address will not be published. Required fields are marked *